![]() ![]() Since a lot of this is quite foreign knowledge to me, maybe it could be good to go over the basics a bit, to see if i understood this properly and that i'm using the proper ip's in the appropriate places.ġ. Yes - that link on HowToGeeks you sent me, was the original post I also followed. You were right, I did say 7 in my initial post - I probably mixed them up during several tries. To open Powershell press on the Windows Key and X at the same time. The final option on the page, Ping Specific Port using Powershell, does work without needing to reboot. You can just type your IP Address a space then the port number since you already have telnet running.įYI the "$" is just the prompt and is not part of a command. You can test that it is working by just typing Make sure you use an elevated command prompt when you type the command. Once you get telnet installed it will have to reboot. If you don't know how to open Control Panel. I just tested this (Option 1) and it works: Apparently Microsoft stopped making it a part of the default installation of Win 10 somewhere among the many updates but it is still available just not with sudo which is a Unix command. Thank you and hope we can make this work! I'll provide any other info or clarifications that are needed. ![]() I am not an expert, not even too much of a tech-savvy, I've done my best to describe what I've done but some confusions may have occurred. router connected via ethernet cable to the PC In the process I didn't pay attention to it, presumed it has no interference. if it matters, got a secondary network card, ASUS PCE-N53 on PCI-E card#2. PC - Asrock X99 Extreme 4 motherboard with onboard Intel I218-V succesfully tested the magic package via a testing tool, with the PC turned on and set the app to "listen" (I'll post a link to the tool if it's needed) - I used my DDNS address for host (ip) address Port 7 MAC address - the one on the back of my router. configured a dynamic DNS through my router, by using the free asus service configured port forwarding to forward port UDP 7 to my network card ip range - 192.168.1.255 enabled magic packet options in both BIOS and network card properties (and it works, as I was able to start it with Anydesk) To be able to WOL through the internet, I've followed some steps described in a few other websites (I can post them if needed) - basically: I've managed to wake up my PC through LAN by using Anydesk however it only works if the other device is connected to the same local network (i mean wake up from shut-down state). I've configured a remote acces through windows and also have an Anydesk account configured (just context). Just watch the Video for more detailed instructions.At my current job sometimes i have to work in remote places i have quite a large library of resources on my home PC that would be great to be accessible remotely. Set up your router for Port Forwarding to the PC in your home or office that you want to connect to.Set up your PC BIOS to enable Wake On Lan.The steps involved in how to set up TeamViewer for wake on lan are fairly straightforward: Why keep your computers on 24/7 just because once in a while you have to log in to work from home or the other way around? Using TeamViewer and configuring Wake On Lan is a perfect solution that allows you to be both environmentally conscious and able to be more productive. If they go into Sleep mode, you won't be able to connect from outside the firewall. ![]() Of course, you could set up a VPN if your Router supports it but that's another layer of complexity.Īnother major problem with the raw port forwarding and Remote Desktop is that you have to keep the computers on at all times. I use TeamViewer software for this purpose. For any real work from home or home accounting from work – or whatever it is you do that you wouldn’t want anyone to snoop on – you need a safe, encrypted tunnel. This strategy works and is a quick and dirty way to connect and do something on the remote computer, but I wouldn't advocate working remotely this way, especially if you need to do anything sensitive. In a previous video and post, I showed you how to set up port forwarding on your router to Allow Remote Desktop Connections from Outside Your Network. I had to learn how to set up TeamViewer for Wake On Lan so that I could log in to my work computer from home and my home computer from work, and allow both computers to go into Sleep Mode in order to save electricity. This post originally appeared on the AppDataWorks blog at ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |